Thank You. I am trying to remote access to my Cisco 897VA Router using pre shared key only through Windows 10, Mac OS X and iPhone builtin IKEv2 VPN. As far as I'm aware that feature is not supported on cEdge platforms, you can only use IPsec tunnels on the Service Side VPN. The information in this document is based on these software and hardware versions: The information in this document was created from the devices in a specific lab environment. Remote Type = 0. . In the IKEv1 Phase 1 settings, you can select one of these modes: Main Mode. #peer R3. Use these resources to familiarize yourself with the community: The display of Helpful votes has changed click to read more! Hi, can you please post the config that solved your problem. I notice the guide was written for the vEdge. We may get it in march release if everything will be on track. Windows or MAC (native or AC) client can only use Certificates or EAP. The address range specifies that all traffic to and from that range is tunneled. I'm unsure if Viptela using IOS XE has this same capability. You can configure IPsec on tunnels for VPN 1 through 65530, except for 512. https://www.cisco.com/c/en/us/td/docs/routers/sdwan/configuration/System-Interface/systems-interfaces-book/configure-interfaces.html. Transport side Ike based IPsec is not available in cedge. ", https://www.cisco.com/c/en/us/td/docs/routers/sdwan/configuration/Security/Security-Book/security-book_chapter_01.html?bookSearch=true#c_Configuring_IKE_Enabled_IPsec_Tunnels_12216.xml. New here? The Notify Payload, is used to transmit informational data, such as error conditions and state transitions, to an IKE peer. You cannot configure IKEv2 through the user interface. An attacker could exploit this vulnerability by sending crafted IKEv2 SA-Init . The CHILD_SA packet typically contains: Router 2 now builds the reply for the CHILD_SA exchange. Bug Details Include 0 Helpful Share Reply JW_UK Beginner In response to JW_UK Options 09-28-2019 03:19 AM Cisco recommends that you have knowledge of the packet exchange for IKEv2. #crypto ikev2 policy cisco. I followed the guide and created the IPSEC interface on the service side instead of VPN0, unfortunately I'm getting a IKEv2 failure: IKEv2:% Getting preshared key from profile keyring if-ipsec1-ikev2-keyringIKEv2:% Matched peer block 'if-ipsec1-ikev2-keyring-peer'IKEv2:(SESSION ID = 0,SA ID = 0):Searching Policy with fvrf 0, local address X.X.X.XIKEv2:(SESSION ID = 0,SA ID = 0):Found Policy 'policy1-global'IKEv2-ERROR:Address type 1622425149 not supported. Tunnel is up on the Responder. Hence, you would see 'PFS (Y/N): N, DH group: none' until the first rekey. Uses certificates for the authentication mechanism. Configure Phase 1 Settings For IKEv1. Hi, made some more tests and my problem is the following, IPSec tunnel can be established if remote end is configured without any specific encryption domains for the communication and with a transport network within the tunnel (for routing purpose - like in GRE Tunnel). In addition, this document provides information on how to translate certain debug lines in a configuration. All traffic must be accepted and specific routing is needed to direct traffic into specific tunnels. Nonce Ni (optional): If the CHILD_SA is created as part of the initial exchange, a second KE payload and nonce must not be sent), KEi (Key-optional): The CREATE_CHILD_SA request might optionally contain a KE payload for an additional DH exchange to enable stronger guarantees of forward secrecy for the CHILD_SA. IPSEC profile: this is phase2, we will create the transform set in here. Router1 verifies and processes the response: (1) The initiator DH secret key is computed, and (2) the initiator skeyid is also generated. Communication over the IPSec Tunnel should be done via VPN1. This module describes the Internet Key Exchange Version 2 (IKEv2) protocol. If the SA offers include different DH groups, KEi must be an element of the group the initiator expects the responder to accept. Description (partial) Symptom: Garbage value (non-comprehensible) seen in the ikev2 error line "Address type 4132115430 not supported" Conditions: When ikev2 error debugging is turned on. The CLI based workaround for it (on cEdge). If your network is live, make sure that you understand the potential impact of any command. The sample configuration connects a Cisco ASA device to an Azure route-based VPN gateway. - edited Responder initiates SA creation for that peer. Select the " Show Advanced Settings " option on the top left and make sure the enable box is checked. This response packet contains: ISAKMP Header(SPI/ version/flags), IDr(responder's identity), AUTH payload, SAr2(initiates the SA-similar to the phase 2 transform set exchange in IKEv1), and TSi and TSr(Initiator and Responder Traffic selectors). This mode is more secure, and uses three . You can also check the output of theshow crypto sessioncommand on both routers; this output shows the tunnel session status as UP-ACTIVE. You can use IKEv2 as a virtual private network (VPN) tunneling protocol that supports automatic VPN reconnection. They contain the source and destination address of the initiator and responder respectively for forwarding/receiving encrypted traffic. Initiator building IKE_INIT_SA packet. Customers Also Viewed These Support Documents, https://www.cisco.com/c/en/us/support/docs/security/flexvpn/115907-config-flexvpn-wcca-00.html. New here? Be aware the static route will only be withdrawn from the routing table if the Tunnel goes down. Refer toCisco Technical Tips Conventionsfor more information on document conventions. Tunnel is up on the Initiator and the status shows. At the moment,you can use service side ipsec in cedge. For more information, refer to IKEv2 Packet Exchange and Protocol Level Debugging. Components Used The information in this document is based on these software and hardware versions: Internet Key Exchange Version 2 (IKEv2) The address range specifies that all traffic to and from that range are tunnelled. If it guesses wrong, the CREATE_CHILD_SA exchange fails, and it will have to retry with a different KEi. 05-18-2021 12:04 PM. #pre-shared-key cisco1234. These debug commands are used in this document: *Nov 11 20:28:34.003: IKEv2:Got a packet from dispatcher *Nov 11 20:28:34.003: IKEv2: Processing an item off the pak queue *Nov 11 19:30:34.811: IKEv2:% Getting preshared key by address 10.0.0.2 *Nov 11 19:30:34.811: IKEv2:Adding Proposal PHASE1-prop to toolkit policyle *Nov 11 19:30:34.811: IKEv2:(1): Choosing IKE profile IKEV2-SETUP *Nov 11 19:30:34.811: IKEv2:New ikev2 sa request admitted *Nov 11 19:30:34.811: IKEv2:Incrementing outgoing negotiating sa count by one. In IKEv1 there was a clearly demarcated phase1 exchange that consisted of six (6) packets followed by a phase 2 exchange that consisted of three (3) packets; the IKEv2 exchange is variable. INFO_R Event: EV_CHK_INFO_TYPE IKEv2-PROTO-5: (99): SM Trace-> SA: I . My template for 'VPN Interface IPsec' looks like this: Then, this template is added under the Service VPN : I thought it was all working fine, however I now have a new problem.IKEv2 is working for Phase 1, but IPSEC is failing.For some reason the ISR4K is creating 16 SA's whilst Zscaler only support a maximum of 8 SA's, therefore the tunnel is currently unusable. 01:52 PM : crypto ikev2 profile default . I believe it is specific to ISR4K's and being fixed in the November code release. All of the devices used in this document started with a cleared (default) configuration. Note: In this output, unlike in IKEv1, the PFS DH group value appears as "PFS (Y/N): N, DH group: none" during the first tunnel negotiation, but, after a rekey occurs, the right values appear. Initiates SA creation, *Nov 11 19:30:34.811: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=0000000000000000 (I) MsgID = 00000000 CurState: IDLE Event: EV_INIT_SA. BR12-1X(config)# crypto ikev2 profile apple, BR12-1X(config-ikev2-profile)# config-exchange request, BR12-1X(config-ikev2-profile)# no config-exchange request. Any luck getting this to work? If the proposal is acceptable to the responder, it sends identical TS payloads back. I also had to mention the same ACL in the local policy for this to work. The sample requires that ASA devices use the IKEv2 policy with access-list-based configurations, not VTI-based. IKEv2 Settings Policy - HQ-VPN Auth Type - Preshared Manual Key Key is set in both fields IPsec Tab: Crypto Map Type - Static IKEv2 Mode - Tunnel Transform Sets IKEv2 Proposals - SHA-256 Enable Reverse Route Injection- Checked Enable PFS - Checked Modulus Group - 19 Lifetime Duration - 28800 Lifetime Size - 4608000 Advanced Tab: Relevant Configuration:crypto ikev2 proposal PHASE1-prop encryption 3des aes-cbc-128 integrity sha1 group 2 crypto ikev2 keyring KEYRNG peer peer2 address 10.0.0.1 255.255.255.0 hostname host2 pre-shared-key local cisco pre-shared-key remote cisco, *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):Next payload: SA, version: 2.0 Exchange type:IKE_SA_INIT,flags:RESPONDER MSG-RESPONSEMessage id: 0, length: 449 Payload contents: SANext payload: KE, reserved: 0x0, length: 48 last proposal: 0x0, reserved: 0x0, length: 44 Proposal: 1, Protocol id: IKE, SPI size: 0, #trans: 4 last transform: 0x3, reserved: 0x0: length: 12 type: 1, reserved: 0x0, id: AES-CBC last transform: 0x3, reserved: 0x0: length: 8 type: 2, reserved: 0x0, id: SHA1 last transform: 0x3, reserved: 0x0: length: 8 type: 3, reserved: 0x0, id: SHA96 last transform: 0x0, reserved: 0x0: length: 8 type: 4, reserved: 0x0, id: DH_GROUP_1024_MODP/Group 2 KENext payload: N, reserved: 0x0, length: 136 DH group: 2, Reserved: 0x0 NNext payload: VID, reserved: 0x0, length: 24 VID Next payload: VID, reserved: 0x0, length: 23 VID Next payload: NOTIFY, reserved: 0x0, length: 21 NOTIFY(NAT_DETECTION_SOURCE_IP) Next payload: NOTIFY, reserved: 0x0, length: 28 Security protocol id: IKE, spi size: 0, type: NAT_DETECTION_SOURCE_IP NOTIFY(NAT_DETECTION_DESTINATION_IP) Next payload: CERTREQ, reserved: 0x0, length: 28 Security protocol id: IKE, spi size: 0, type: NAT_DETECTION_DESTINATION_IP CERTREQ Next payload: NOTIFY, reserved: 0x0, length: 105 Cert encoding Hash and URL of PKIX NOTIFY(HTTP_CERT_LOOKUP_SUPPORTED) Next payload: NONE, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: HTTP_CERT_LOOKUP_SUPPORTED, *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: INIT_DONE Event: EV_DONE *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):Cisco DeleteReason Notify is enabled *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: INIT_DONE Event: EV_CHK4_ROLE *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: INIT_DONE Event:EV_START_TMR *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_WAIT_AUTH Event: EV_NO_EVENT *Nov 11 19:30:34.822: IKEv2:New ikev2 sa request admitted *Nov 11 19:30:34.822: IKEv2:Incrementing outgoing negotiating sa count by one, *Nov 11 19:30:34.823: IKEv2:Got a packet from dispatcher *Nov 11 19:30:34.823: IKEv2:Got a packet from dispatcher *Nov 11 19:30:34.823: IKEv2:Processing an item off the pak queue, I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: INIT_DONE Event:EV_START_TMR, *Nov 11 19:30:34.823: IKEv2:(SA ID = 1):Next payload: SA, version: 2.0 Exchange type: IKE_SA_INIT, flags:RESPONDER MSG-RESPONSEMessage id: 0, length: 449 Payload contents: SANext payload: KE, reserved: 0x0, length: 48 last proposal: 0x0, reserved: 0x0, length: 44 Proposal: 1, Protocol id: IKE, SPI size: 0, #trans: 4 last transform: 0x3, reserved: 0x0: length: 12 type: 1, reserved: 0x0, id: AES-CBC last transform: 0x3, reserved: 0x0: length: 8 type: 2, reserved: 0x0, id: SHA1 last transform: 0x3, reserved: 0x0: length: 8 type: 3, reserved: 0x0, id: SHA96 last transform: 0x0, reserved: 0x0: length: 8 type: 4, reserved: 0x0, id: DH_GROUP_1024_MODP/Group 2 KENext payload: N, reserved: 0x0, length: 136 DH group: 2, Reserved: 0x0 NNext payload: VID, reserved: 0x0, length: 24 *Nov 11 19:30:34.823: IKEv2:Parse Vendor Specific Payload: CISCO-DELETE-REASON VID Next payload: VID, reserved: 0x0, length: 23 *Nov 11 19:30:34.823: IKEv2:Parse Vendor Specific Payload: (CUSTOM) VID Next payload: NOTIFY, reserved: 0x0, length: 21 *Nov 11 19:30:34.823: IKEv2:Parse Notify Payload: NAT_DETECTION_SOURCE_IP NOTIFY(NAT_DETECTION_SOURCE_IP) Next payload: NOTIFY, reserved: 0x0, length: 28 Security protocol id: IKE, spi size: 0, type: NAT_DETECTION_SOURCE_IP *Nov 11 19:30:34.824: IKEv2:Parse Notify Payload: NAT_DETECTION_DESTINATION_IP NOTIFY(NAT_DETECTION_DESTINATION_IP) Next payload: CERTREQ, reserved: 0x0, length: 28 Security protocol id: IKE, spi size: 0, type: NAT_DETECTION_DESTINATION_IP CERTREQ Next payload: NOTIFY, reserved: 0x0, length: 105 Cert encoding Hash and URL of PKIX *Nov 11 19:30:34.824: IKEv2:Parse Notify Payload: HTTP_CERT_LOOKUP_SUPPORTED NOTIFY(HTTP_CERT_LOOKUP_SUPPORTED) Next payload: NONE, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: HTTP_CERT_LOOKUP_SUPPORTED, *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_WAIT_INIT Event: EV_RECV_INIT *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):Processing IKE_SA_INIT message *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_PROC_INIT Event: EV_CHK4_NOTIFY *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_PROC_INIT Event: EV_VERIFY_MSG *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_PROC_INIT Event: EV_PROC_MSG *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_PROC_INIT Event: EV_DETECT_NAT *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):Process NAT discovery notify *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):Processing nat detect src notify *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):Remote address matched *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):Processing nat detect dst notify *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):Local address matched *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):No NAT found *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_PROC_INIT Event: EV_CHK_NAT_T *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_PROC_INIT Event: EV_CHK_CONFIG_MODE *Nov 11 19:30:34.824: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: INIT_DONE Event:EV_GEN_DH_SECRET *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: INIT_DONE Event: EV_NO_EVENT *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: INIT_DONE Event: EV_OK_RECD_DH_SECRET_RESP *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):Action: Action_Null *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: INIT_DONE Event:EV_GEN_SKEYID *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):Generate skeyid *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: INIT_DONE Event: EV_DONE *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):Cisco DeleteReason Notify is enabled *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: INIT_DONE Event: EV_CHK4_ROLE *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event: EV_GET_CONFIG_MODE *Nov 11 19:30:34.831: IKEv2:Sending config data to toolkit *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event: EV_CHK_EAP. Local Type = 0. The packet exchange in IKEv2 is radically different from packet exchange in IKEv1. This exchange consists of a single request/response pair and was referred to as a phase 2 exchange in IKEv1. Click the Add button to insert a new VPN rule. Cisco recommends that you have knowledge of the packet exchange for IKEv2. Beginner. Nonce Ni(optional): If the CHILD_SA is created as part of the initial exchange, a second KE payload and nonce must not be sent. You cannot use PSK for authentication of a Remote Access FlexVPN, see this screenshot below from Cisco live presentation BRKSEX-2881. I've tried domain\user, [email protected] and just plain user. Local Address = 0.0.0.0. The DH Group configured under the crypto map would be used only during rekey. It might be initiated by either end of the IKE_SA after the initial exchanges are completed. Cisco recommends that you have knowledge of the packet exchange for IKEv2. I'd be interested to hear if you have the same issue? Relevant Configuration:crypto ikev2 proposal PHASE1-prop encryption 3des aes-cbc-128 integrity sha1 group 2crypto ikev2 keyring KEYRNG peer peer1 address 10.0.0.2 255.255.255.0 hostname host1 pre-shared-key local cisco pre-shared-key remote cisco, *Nov 11 19:30:34.814: IKEv2:Got a packet from dispatcher *Nov 11 19:30:34.814: IKEv2:Processing an item off the pak queue *Nov 11 19:30:34.814: IKEv2:New ikev2 sa request admitted *Nov 11 19:30:34.814: IKEv2:Incrementing incoming negotiating sa count by one, *Nov 11 19:30:34.814: IKEv2:Next payload: SA, version: 2.0 Exchange type: IKE_SA_INIT, flags: INITIATOR Message id: 0, length: 344 Payload contents: SA Next payload: KE, reserved: 0x0, length: 56 last proposal: 0x0, reserved: 0x0, length: 52 Proposal: 1, Protocol id: IKE, SPI size: 0, #trans: 5 last transform: 0x3, reserved: 0x0: length: 8 type: 1, reserved: 0x0, id: 3DES last transform: 0x3, reserved: 0x0: length: 12 type: 1, reserved: 0x0, id: AES-CBC last transform: 0x3, reserved: 0x0: length: 8 type: 2, reserved: 0x0, id: SHA1 last transform: 0x3, reserved: 0x0: length: 8 type: 3, reserved: 0x0, id: SHA96 last transform: 0x0, reserved: 0x0: length: 8 type: 4, reserved: 0x0, id: DH_GROUP_1024_MODP/Group 2 KE Next payload: N, reserved: 0x0, length: 136 DH group: 2, Reserved: 0x0 N Next payload: VID, reserved: 0x0, length: 24 *Nov 11 19:30:34.814: IKEv2:Parse Vendor Specific Payload: CISCO-DELETE-REASON VID Next payload: VID, reserved: 0x0, length: 23 *Nov 11 19:30:34.814: IKEv2:Parse Vendor Specific Payload: (CUSTOM) VID Next payload: NOTIFY, reserved: 0x0, length: 21 *Nov 11 19:30:34.814: IKEv2:Parse Notify Payload: NAT_DETECTION_SOURCE_IP NOTIFY(NAT_DETECTION_SOURCE_IP) Next payload: NOTIFY, reserved: 0x0, length: 28 Security protocol id: IKE, spi size: 0, type: NAT_DETECTION_SOURCE_IP *Nov 11 19:30:34.814: IKEv2:Parse Notify Payload: NAT_DETECTION_DESTINATION_IP NOTIFY(NAT_DETECTION_DESTINATION_IP) Next payload: NONE, reserved: 0x0, length: 28 Security protocol id: IKE, spi size: 0, type: NAT_DETECTION_DESTINATION_IP, *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: IDLE Event:EV_RECV_INIT *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event:EV_VERIFY_MSG *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event:EV_INSERT_SA *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event:EV_GET_IKE_POLICY *Nov 11 19:30:34.814: IKEv2:Adding Proposal default to toolkit policy *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event:EV_PROC_MSG *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event: EV_DETECT_NAT *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Process NAT discovery notify *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Processing nat detect src notify *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Remote address matched *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Processing nat detect dst notify *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Local address matched *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):No NAT found *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event: EV_CHK_CONFIG_MODE *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_SET_POLICY *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Setting configured policies *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_CHK_AUTH4PKI *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_PKI_SESH_OPEN *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Opening a PKI session *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event:EV_GEN_DH_KEY *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_NO_EVENT *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event:EV_OK_RECD_DH_PUBKEY_RESP *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):Action: Action_Null *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event:EV_GEN_DH_SECRET *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_NO_EVENT *Nov 11 19:30:34.822: IKEv2:%Getting preshared key by address 10.0.0.1 *Nov 11 19:30:34.822: IKEv2:Adding Proposal default to toolkit policy *Nov 11 19:30:34.822: IKEv2:(2): Choosing IKE profile IKEV2-SETUP *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_OK_RECD_DH_SECRET_RESP *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):Action: Action_Null *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event:EV_GEN_SKEYID *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):Generate skeyid *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_GET_CONFIG_MODE *Nov 11 19:30:34.822: IKEv2:IKEv2 responder - no config data to send in IKE_SA_INIT exch *Nov 11 19:30:34.822: IKEv2:No config data to send to toolkit: *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_BLD_MSG *Nov 11 19:30:34.822: IKEv2:Construct Vendor Specific Payload: DELETE-REASON *Nov 11 19:30:34.822: IKEv2:Construct Vendor Specific Payload: (CUSTOM) *Nov 11 19:30:34.822: IKEv2:Construct Notify Payload: NAT_DETECTION_SOURCE_IP *Nov 11 19:30:34.822: IKEv2:Construct Notify Payload: NAT_DETECTION_DESTINATION_IP *Nov 11 19:30:34.822: IKEv2:Construct Notify Payload: HTTP_CERT_LOOKUP_SUPPORTED.

North Port High School Bell Schedule, Icourt Smart Search, Shabba Doo Cause Of Death, Articles C